Bodyguard Treadmills Owner's Manual Page 1

T280P – T280C – T300TREADMILLS OWNER’S MANUAL Part no: 691022T280P illustratedBODYGUARD®FITNESS, division of Procycle CANADA 9095, 25thAvenue, Saint-G

10 2.4 User Identification Feature The User Identification feature allows the treadmill to recognize individuals and automatically enter their weight

11Reset Statistics To reset the statistics of a User Identification: Select the RESET STATISTICS option and press JustGoTM/ENTER key to accept. Select

12NOTE– The default value of the warm up is 3 minutes. The cool down has an adjustable duration of one to four minutes and has only one part. Cool

132.10 Beeper Feature The beeper can be activated or deactivated. To activate or deactivate the beeper: 1. Enter into the Settings menu, see Section

14 2.14 Heart Rate Recovery Your T280P–T280C–T300 is pre programmed with a unique and useful program that is used to help determine your fitness level

15Program Levels The Cardiovascular, Interval, Random, Hill Climb and Speed Run programs have 5 individual exercise levels. LEVEL 1 is the easiest and

16The following table shows the different speeds and elevations for each level. Level Speed (mph) Speed (km/h) Elevation (%) 1 0.5 t

17During the Heart Rate Control or Weight Loss program, you can change the speed or elevation by pressing the Speed or Elevation INCREASE or DECREASE

18Track Program The Track program is one that enables you to choose from 1-99 laps of a 400 Meter (or about a 1/4 mile) Olympic track. Each Track pro

19Using Contact Heart Rate This machine has a built-in Contact Heart Rate System that allows you to verify your heart rate without the need of a chest

20Possible Chest Strap Heart Rate Problems All Bodyguard® machines are compatible with the Polar wireless heart rate system. This includes a chest str

21The T280P–T280C–T300 treadmills allow you to perform the following tests: • NVRAM TEST • EPROM TEST • KEYPAD TEST• DISPLAY TEST• BEEPER

22Belt Alignment Should you need to adjust the tracking of the running belt, you must make all adjustments during the BELT ALIGNMENT procedure. To d

231. In the Diagnostics menu, select the “ELEVATION CALIBRATION” and accept it by pressing the JustGoTM/ENTER key. 2. Press the JustGoTM /ENTER key t

24Maintenance The maintenance menu allows you to see the average value of the current drawn by the motor. It also allows you to reset this counter. A

1 2 4 5 1 2 3 6 25Belt and Running Deck Running Belt The running belt supplied with each treadmill is of the highest quality, offering superi

26Lubricant Application 1. Clean the deck surface and the inside part of the belt with a dry piece of fabric. Clean the belt first by using a long pie

27Error Codes Table 4 PROBLEME CAUSE / SOLUTION • Error 1 • Acceleration is too quick in the acceleration or reached speed phase. • Possible causes

28Safety Requirements North America The T280P–T280C–T300 treadmills have been tested and approved to meet all ETL requirements concerning electrical a

29

3Table of Contents IMPORTANT SAFETY NOTICE ...

30

4Important Safety Notice READ THIS MANUAL THOROUGHLY BEFORE ATTEMPTING TO ASSEMBLE OR USE THIS EXERCISE EQUIPMENT. To ensure that you get the maximum

5Electrical Information CAUTION – This equipment is intended to be electrically grounded. The three-wire grounding plug (polarized) will fit only a gr

Enter key Central information window Speed profile (bright green) Elevation profile (light green) Other programs key Flashing dot under profiles ind

7Each exercise program starts from the left part of the screen and terminates when it reaches the right part of the screen. A flashing dot will indic

8Scanning Feature During an exercise you will be able to view nine scanning exercise parameters on the central informational window along with the ex

91.4 Viewing Exercise Parameters At the end of each exercise program, the computer will display four exercise parameters. These parameters will be TO